架F将近一个月了，找遍了所有可能引起跳ping的原因。总结出了一点经验，与大家共享，也感谢DT会员。
1、CS服务器3647最稳定，没有自动踢人的现象，推荐采用。本人用的DT3647纯净版服务端，最好是纯净版，保持服务器纯净不含其它config
2、Metamod 1.19 p32 或p28 ，个人觉得比较稳定。
3、Amxmod我个人用的是1.76b ，感觉挺稳定的。
4、Booster 这个很重要，推荐用1.7版本。
其实不必追求过高的FPS，一般服务器保持在200左右是最稳定的。在512-200 左右来回跳频是容易造成ping不稳定。感谢DT会员Zsy314发的Booster.cfg参数，我再贴一下，这个Booster.cfg将接管CPU，将服务器fps保持在稳定的数值内。
将以下内容复制至文本文件中，改名booster.cfg。^_^
server.cfg中加一行exec booster.cfg ，每次换图时自动锁定fps值。
=============== 以下是Booster.cfg内容============================
sys_ticrate 1000
// booster_show_connmsg x (0 = disabled, 1 = small message, 2 = large message)
// Shows a console message to players with booster information when they connect.
booster_show_connmsg 1
// booster_autofps x (x = 0 to 1000, 0 = no target FPS)
// Automatically changes value of sys_ticrate to achieve and maintain the desired server FPS (if possible).
// It is not recommended to target FPS greater than 200 or so.
// Note that autofps adjusts sys_ticrate, which makes it incompatible with any booster_lite_mode other
// than 3. Setting booster_autofps will force booster_lite_mode to 3.
booster_autofps 1000
// booster_minsleepms x (x = 1 to 10, 10 = no change to multimedia timer)
// This adjusts the multimedia system timer to trick HLDS into sleeping for less time. Note that
// the lower the value set, the higher the CPU consumption will be for HLDS. Values lower than 3
// are not recommended, as they can cause massive CPU consumption and/or system instability.
booster_minsleepms 5
// booster_force_systicrate x (x = 0 to 10000, 0 = let Booster2 manage the value itself (no force))
// Booster2 will force this sys_ticrate value. Note that using this option will set booster_autofps to 0
// and booster_lite_mode to 3, as these methods rely on a sys_ticrate value untouched by user settings.
// You should avoid directly setting sys_ticrate in your server.cfg, as manually adjusted values can
// cause problems with various parts of Booster2.
booster_force_systicrate 0
// booster_cpu_enabled x [0 to 2] (0 = off, 1 = on, 2 = report CPU only - don't actively manage CPU)
// Booster2 can monitor CPU usage and adjust the multimedia timer to reduce load when necessary
booster_cpu_enabled 0
// booster_cpu_spikemax x
// If CPU management is enabled, number of times booster_cpu_spikelevel needs
// to be exceeded in order for mmtimer to increase and CPU load to be reduced.
booster_cpu_spikemax 3
// booster_cpu_spikelevel x [0 to 100]
// If CPU management is enabled, level which CPU utilization needs to exceed
// (booster_cpu_spikemax times) for mmtimer to increase and CPU load to be reduced.
booster_cpu_spikelevel 75
// booster_cpu_floor x [0 to 100]
// If CPU management is enabled, level which CPU utilization needs to stay under
// (for booster_cpu_quiettime seconds) for mmtimer to decrease and FPS to increase.
booster_cpu_floor 50
// booster_cpu_mminc x [1 to 10]
// If CPU management is enabled, amount mmtimer will increment (Booster2 will also decrease
// the mmtimer by 1 for every 5 minute period that booster_cpu_spikelevel is not exceeded.
booster_cpu_mminc 2
// booster_cpu_quiettime
// Seconds required without CPU spike exceeding booster_cpu_floor before
// mmtimer value is decreased by 1.
booster_cpu_quiettime 300
// booster_cpu_mmmin x [1 to 10]
// If CPU management is enabled, Booster2 will never set the mmtimer below this value.
booster_cpu_mmmin 3
// booster_cpu_mmmax x [1 to 10]
// If CPU management is enabled, Booster2 will never set the mmtimer above this value.
booster_cpu_mmmax 8
// booster_lite_mode x [0 to 3]
// Controls how the Booster-Lite approach is implemented:
// 0 - HLDS sleeps 10ms if no network packets are received. If HLDS
// receives a packet, it stops sleeping. (this mode has been added
// to provide backward compatibility with how BL v1.00 worked).
// 1 - HLDS attempts to sleep 10ms. If a packet is received,
// HLDS stops sleeping. Otherwise it attempts to sleep another 10ms.
// 2 - HLDS attempts to sleep 50ms. If a packet is received, it stops sleeping.
// 3 - HLDS will sleep the standard amount (this value turns this feature off).
booster_lite_mode 3
// booster_lite_extra_sleep_frequency x
// Forces HLDS server to sleep x milliseconds even if a packet is received.
// This setting helps to lower CPU usage.
booster_lite_extra_sleep_frequency 0
// booster_stats_cpu_counter
// Sets the string Booster will use to query cpu performance. By default this is
// "\Processor(_Total)\% Processor Time". Manually set this only if you need to
// support non-english counter names or to query a specific processor.
// This cvar is only used if booster_cpu_enabled is turned on.
// booster_stats_in_counter
// Sets the string Booster will use to query bandwidth in. By default this is
// "\Network Interface(NDIS 5.0 driver)\Bytes Received/sec". Manually set this only
// if you need to support non-english counter names or to query a specific interface.
// This cvar is only used if booster_stats is turned on.
// booster_stats_out_counter
// Sets the string Booster will use to query bandwidth out. By default this is
// "\Network Interface(NDIS 5.0 driver)\Bytes Sent/sec". Manually set this only
// if you need to support non-english counter names or to query a specific interface.
// This cvar is only used if booster_stats is turned on.
// booster_stats [0-1]
// This turns on statistics gathering. This options is not supported. See info at the end
// of the readme regarding this option.
// booster_trigger_cmd
// Sets a command to be executed the first time (during any given map) that CPU consumption
// trips booster_cpu_spikemax. This allows admins to do things such as turn off wallhack
// blocks or other CPU intensive systems under heavy load.
// booster_intping
// This is a read-only value, and holds the current average player ping.
// booster_extping
// This is a read-only value, and holds the current ping to the address set in booster_pingaddr.
// booster_pingaddr
// Sets the address (in IP format x.x.x.x) that Booster will ping once a minute. If no value is
// set, Booster won't ping anything. Pinging an external address is useful in helping determine
// latency issues. If clients are showing high ping, pings to a nearby router can help determine
// if the problem is close to the server or part of something that is beyond the administrator's
// control.
====================我是分割线====================================
我机子基本锁定在200左右，20人服务器，个人认为足够保持稳定的ping值了。
最后强调一点，CS服务器如果配置不够强，最好只运行CS服务器。不要运行其它非CS程序，可能导致跳ping ，本人有过这样的经验。
本文来自:深蓝海洋技术博客(www.deepcn.net)
原文链接：http://www.deepcn.net/view.asp?id=173 |
IP卡
狗仔卡
发表于 2008-10-18 12:57:38
提升卡
置顶卡
沉默卡
喧嚣卡
变色卡
显身卡